Industrial Gear Oils

ENDURATEX™ EP gear oils are premium performance, extreme pressure lubricants designed for enclosed industrial gears and bearings operating under severe load conditions and in extreme temperatures.

ENDURATEX™ XL Synthetic Blend 68/150 and 68/220 are multi-grade gear oils are premium performance lubricants designed with all the same benefits, but with the additional advantage of eliminating the need for seasonal change outs. These multigrades complete the line, by extending AGMA EP viscosities over an extended temperature range. The 68/220 supports winter requirements (68 grade) and summer requirements (220 grade). The 68/150 delivers excellent low temperature properties versus leading all season competitive products for easier cold start-ups and better equipment protection.

ENDURATEX™ EP gear oils are suitable for use in most industrial gear sets that require a high quality EP lubricant.

ENDURATEX™ EP gear oils are typically suitable for use in situations requiring DIN 51517 Part 3, ISO 12925 – Type 1 CKC, AGMA 9005-F16, and AIST 224 (formerly US Steel 224) specifications.

The following products meet the specifications for ISO 12925-1 CKD:

• ENDURATEX™ Synthetic EP (Refer to Table)

• ENDURATEX™ XL Synthetic Blend 68/150 and 68/220

• ENDURATEX™ EP 32, 68, 100, 150 and 220

Fives Cincinnati (formerly MAG-IAS) Approval

ENDURATEX™ EP 150     P-77   ENDURATEX™ EP 220     P-74
ENDURATEX™ EP 320     P-59   ENDURATEX™ EP 460     P-35
ENDURATEX™ EP 460 is approved for Caterpillar Global Mining LLC (formerly Bucyrus International Inc.) Dragline enclosed gearcase lubricant (SD4721 Part A).

Typical characteristics are shown below:

ENDURATEX™ Mild WG oils are non-EP lubricants recommended for service in some enclosed worm gear reducers and industrial machinery. ENDURATEX™ Mild WG oils are also suited for lubrication of reciprocating steam cylinders.

Typical characteristics are shown below:

ENDURATEX™ Synthetic OHV (Off-Highway Vehicle) 680 is a premium performance, extreme pressure lubricant. It is designed to work in high temperature conditions and maintain exceptional lubricant film strength. Formulated using PAO and ester-based technology, this product is capable of withstanding severe load conditions, helping to reduce wear so that component life is maximized. It is approved by General Electric for the lubrication of both DC and AC motorized wheel gearbox applications in off- highway haul trucks.

ENDURATEX™ Synthetic OHV 680 is also suitable for use in stationary gearbox applications requiring an ISO 680 viscosity grade.

Typical characteristics are shown below:

ENDURATEX™ Synthetic EP gear oils are premium performance, extreme pressure lubricants designed for enclosed industrial gears and bearings operating under severe load conditions for all-season use. They deliver excellent wear properties and outstanding extreme temperature performance for extended component and fluid life. ENDURATEX™ Synthetic EP enhances gear box performance over a wide temperature range. The high viscosity index of ENDURATEX™ Synthetic EP gear oils means that they retain their viscosity at high operating conditions. This often allows the use of a lower ISO grade than with conventional gear oils. ENDURATEX™ Synthetic EP gear oils meet the requirements of Flender Gear Units Revision 16, AIST 224 (formerly US Steel 224), DIN 51517-3, David Brown S1.53.101 Type E, Fives Cincinnati (formerly MAG IAS), Eickhoff Gear, Jahnel Kestermann and qualify as premium synthetic EP gear lubricants. ENDURATEX™ Synthetic EP gear oils can be used where AGMA antiscuff/antiwear Extreme Pressure (EP) Gear lubricants are required.

ENDURATEX™ Synthetic EP gear oils (ISO 150, 220, 320 and 460) are listed on Flender Gear Units and Geared Motors T7300 Approved Lubricants List and are suitable for use in GE787/GE788 drive systems.

Typical characteristics are shown below:

HARNEX™ 320 is a premium synthetic gear lubricant designed to provide exceptional anti-wear/EP performance, outstanding protection against micropitting and corrosion in wind turbine applications. The product uses synthetic PAO base oils, known for their excellent viscosity index and low pour point properties.

HARNEX™ 320 has Moventas approval for wind turbine gearboxes and also GE service fill approval for 1.x and 2.x platforms with Winergy gearboxes.

HARNEX™ 320 meets the technical requirements of Shanghai Electric, and is approved for use in any gear box on a Shanghai Electric wind turbine. Please contact a Technical Services Advisor for additional information.

In addition, HARNEX™ 320 meets the following industry requirements: AGMA 9005-F16, DIN 51517-3 (CLP 320).

Typical characteristics are shown below:

SYNDURO™ SHB fluids are a family of synthetic multi-functional lubricants designed to deliver excellent component protection for equipment operating at high speed or mild Extreme Pressure (EP) loads over a wide temperature range during extended service intervals. They have the added advantage of excellent low-temperature fluidity during start-ups, or during outdoor winter exposure.

They are especially suitable for a wide range of gear, bearing and compressor applications in the forestry, mining, marine and heavy-duty industries where low seasonal start-up temperatures and/or high operating temperatures prevail. SYNDURO™ SHB 32, 46 and 68 can also be used in rotary screw air compressors at air discharge temperatures up to 93°C/200°F, or as synthetic hydraulic fluids. SYNDURO™ SHB 220 can be used in the timing gears of most dry rotary blowers. SYNDURO™ SHB 460 can be used in moderately loaded worm gearboxes. SYNDURO™ SHB 46 meets Voith Doc. 3625-008377 and is therefore suitable for lubrication of the Vorecon variable speed planetary gear type RWE11F6. SYNDURO™ SHB fluids offer the potential to consolidate lubricants over many different applications and a wide range of operating conditions. For those applications that are subjected to heavy loads or shock loading and require an AGMA 9005-F16 (antiscuff) type of fluid, Petro-Canada Lubricants ENDURATEX™ Synthetic EP series or ENDURATEX Synthetic OHV 680 is recommended.

Typical characteristics are shown below: