SENTRON™ CG 40 PLUS

SENTRON™ CG 40 PLUS (0.52% wt ash) is a uniquely designed low ash formula for 4-cycle stationary gas engines running in biogas, sewage gas and landfill gas operations. It provides excellent control of deposits and offers protection against corrosion caused by high halogen levels produced by landfills. Unlike conventional landfill / biogas / sewer gas engine oils, SENTRON™ CG 40 PLUS is specifically designed to address current and future engines running in this severe contaminated gas application where higher BMEP engines are used.

SENTRON™ LD 3000

SENTRON™ LD 3000 (0.47% wt ash) is recommended for most 4-cycle and some 2-cycle stationary gas engines including Caterpillar, Waukesha and others in gas compression applications. It is suitable for use in engines fitted with catalytic converters. Can be used in any stationary application – compression, power gen, water pumping etc. SENTRON™ LD 3000 helps provide a high level of performance in high output turbocharged and naturally aspirated engines that prefer a low ash oil. It provides excellent control of engine deposits, even when there is a need for added high temperature deposit control. It is suitable for severe service applications including high output, turbocharged engines that encounter high exhaust gas temperatures.

SENTRON™ LD 5000

SENTRON™ LD 5000 (0.57% wt ash) is a low ash SAE 40 oil recommended for use in Caterpillar, Jenbacher, Waukesha, and many turbocharged or naturally aspirated, stoichiometric or lean burn engines that require a low ash stationary gas engine oil. It incorporates additives for the extra performance required for severe service applications, including high output, turbocharged engines that encounter high exhaust gas temperatures. SENTRON™ LD 5000 offers outstanding deposit control and excellent performance for up to 200%* longer drain intervals and exceptional overall engine protection for maximum reliability and savings. It can be used in biogas/digester gas applications if the fuel sources are pre-treated to minimize harmful acidic constituents.

* All data generated were on engines in gas compression service under >90% engine load using pipeline quality fuel and typical field conditions. Performance results may vary due to factors such as, but not limited to, engine optimization, load, fuel gas quality, proper maintenance, type of engine and application.

SENTRON™ LD 8000

SENTRON™ LD 8000 (0.52% wt ash) is a premium low ash SAE 40 lubricant, suitable for use in 4–cycle stationary gas engines operating on natural pipeline gas, pre-treated sewage/biogas and selective pre-treated process gases. It provides revolutionary extended drain intervals over the leading global conventional competitor.* SENTRON™ LD 8000 contains a specialized additive mix that provides greater TBN retention to help neutralize acids that can attack component surfaces. SENTRON™ LD 8000 prevents ash deposits which reduces wear. SENTRON™ LD 8000 combines a high degree of oxidative stability with nitration resistance.

* In Caterpillar G3500 TALE engines running in gas compression, with >90% loads and pipeline quality fuel. Performance results may vary due to factors such as, but not limited to, engine optimization, load, fuel gas quality, proper maintenance, type of engine and application.

SENTRON™ LD SYNTHETIC BLEND

SENTRON™ LD Synthetic Blend (0.53% wt ash) is an SAE 15W-40 multigrade extension of the SENTRON™ line, formulated as a synthetic blend to extend drain intervals and give better low temperature performance in comparison to mono-grade SAE 40 oils. SENTRON™ LD Synthetic Blend is specifically recommended for use in large bore engines prone to excessive combustion chamber deposits. It is suited for colder environments where start up temperatures fall as low as -20°C/-13°F.

SENTRON™ VTP 0W-30

SENTRON™ VTP 0W-30 (0.58% wt ash) is a low ash, synthetic blend stationary gas engine oil formulated specifically as an all season solution for small to mid-sized engines that are difficult to start in severe winter conditions. With a Pour Point of -45°C/-49°F, SENTRON™ VTP 0W-30 helps provide exceptional performance in extreme winter conditions, presenting opportunities for inventory consolidation. SENTRON™ VTP 0W-30 may also be suitable for use in engines equipped with certain on-road catalytic converters. Check with your Technical Services Advisor for suitability.

SENTRON™ VTP 10W-40

SENTRON™ VTP 10W-40 (0.59% wt ash) is specially formulated to meet the demands of small stationary natural gas engines for exceptional cleanliness of the engine through all seasons. It is recommended for use in gas fuelled engines that require high zinc additive for improved valve train wear protection while providing excellent cold start capability. SENTRON™ VTP 10W-40 is suitable for use in applications where Cummins CES 20074 is specified. SENTRON™ VTP 10W-40 may also be suitable for use in engines equipped with certain on-road catalytic converters. Check with your Technical Services Advisor for suitability.

SENTRON™ VLA 40

SENTRON™ VLA 40 (0.30% wt ash) is a “very” low ash stationary gas engine oil, specifically designed for 4-cycle stationary gas engines running at low loads (<60% MCR). Low load engines tend to have increased oil consumption rates, leading to excessive ash deposit accumulation. The very low ash content of 0.30% in SENTRON™ VLA 40 will provide optimal protection against deposit formation preventing excessive combustion chamber deposit buildup, reducing piston ring sticking/breaking and spark plug fouling. The decision to use this product is technical, check with your Technical Services Advisor for further information.