HYDREX™ MV fluids are premium performance, energy efficient, long-life, anti-wear hydraulic fluids designed for use over wide temperature ranges. HYDREX™ MV fluids are recommended for heavy-duty hydraulic applications operating at high pressure and with wide ranges of temperature. They are ideally suited for piston, gear and vane hydraulic pumps used in industrial, marine, woodlands, mining and other mobile hydraulic systems. These fluids offer minimal fluid friction at low start-up temperatures and maintain optimum viscosity at high operating temperatures. Combined with their shear stable high viscosity index, this energy efficient formulation helps your bottom line.

HYDREX™ MV fluids¹ are approved against the following hydraulic equipment manufacturers’ specifications: Eaton E-FDGN-TB002-E, Denison HF-0, HF-1 and HF-2 (MV 32, 46, and 68), and HYDREX™ MV 32, 46 and 68 have also been successfully evaluated against Bosch Rexroth requirements. HYDREX™ MV fluids are suitable for use in equipment manufactured by Eaton, Denison, Bosch Rexroth, Komatsu, Sauer-Danfoss, Oilgear, Hydreco, Dynex and others.

HYDREX™ MV meets the following specifications: ISO 11158 HV, DIN 51524 Part 3 HVLP, ASTM D6158 HV, as well as Fives Cincinnati P-68 (AW 32), P-70 (AW 46) and P-69 (AW 68). HYDREX™ MV 46 also meets the requirements of JCMAS HK and Komatsu HPV35+35 pump test. HYDREX™ MV 32 is suitable for use where JCMAS HK is required. HYDREX™ MV 46 and 68 are suitable for use where AIST 126 and 127 are required. All HYDREX™ MV fluids are NSF H2 registered (no allowable food contact).

HYDREX™ MV Arctic 15 is a premium, high performance hydraulic fluid designed for extremely cold temperature operations, particularly in arctic climates, allowing hydraulic systems to start at temperatures of -50°C (-58°F) under no-load conditions. It is also readily biodegradable as measured by OECD 301B and recommended for use in emergency shut-down valves or other critical low temperature heavy-duty hydraulic systems that are required to respond quickly and reliably.

Typical characteristics are shown below:

¹  Start-up is defined as the temperature at which the oil dynamic viscosity reaches 10,000 cP.

²  Operating temperature limits are determined by the equipment manufacturer. Petro-Canada Lubricants has chosen to define the upper operating temperature to be the after-shear oil kinematic viscosity of 10 cSt for mobile equipment and 13 cSt for industrial machinery, while the lower operating temperature to be the fresh oil dynamic viscosity of 750 cP for both mobile and industrial machinery.

These ranges are only an approximation and the operator should always check the viscosity requirements as specified by their equipment manufacturer. Mobile equipment typically refers to machinery that encompasses a transmission and braking system to allow and prohibit movement. Industrial machinery is typically stationary, with hard piping and auxilliary components in place.

HYDREX™ XV All Season is an advanced formula, long life, energy efficient anti-wear hydraulic fluid designed for all season use in heavy-duty hydraulic systems for increased productivity in very hot or cold temperatures. HYDREX™ XV is recommended for year-round use in equipment that has to be started at temperatures as low as -34°C (-29°F) and it will continue to perform well at operating temperatures as high as 90°C (194°F). HYDREX™ XV gives excellent results in a wide range of industrial machinery and mobile equipment used in such industries as forestry, construction, mining, injection molding, public utility and marine operations. With a very high viscosity index, this energy efficient formulation helps maximize productivity and eliminates the need to change hydraulic oil seasonally.

HYDREX™ XV is approved against the following hydraulic equipment manufacturers specifications: Denison HF-0, HF-1 and HF-2, and Danfoss (Eaton) E-FDGN-TB002-E.

HYDREX™ XV is also suitable for use in equipment manufactured by Bosch Rexroth, Komatsu, Dynex, Hydreco, Oilgear, Marlen and others.

HYDREX™ XV meets the following industrial standards: ISO 11158 HV, DIN 51524 Part 3 HVLP, and ASTM D6158 HV.

HYDREX™ XV is suitable for use where AIST 126 and 127, and JCMAS HK specifications are required. It meets JCMAS HK requirements for Rexroth A2F10 pump test.

Typical characteristics are shown below:

¹ Start-up is defined as the temperature at which the oil dynamic viscosity reaches 10,000 cP.

² Operating temperature limits are determined by the equipment manufacturer. Petro-Canada Lubricants has chosen to define the upper operating temperature to be the after-shear oil kinematic viscosity of 10 cSt for mobile equipment and 13 cSt for industrial machinery, while the lower operating temperature to be the fresh oil dynamic viscosity of 750 cP for both mobile and industrial machinery.

These ranges are only an approximation and the operator should always check the viscosity requirements as specified by their equipment manufacturer. Mobile equipment typically refers to machinery that encompasses a transmission and braking system to allow and prohibit movement. Industrial machinery is typically stationary, with hard piping and auxiliary components in place.

HYDREX™ EXTREME is a high performance multi-grade hydraulic fluid designed for extremely wide temperature protection. Its excellent oxidation stability helps to extend drains and reduce sludge build-up and varnish deposits. HYDREX™ EXTREME is also zinc-free, inherently biodegradable and contains no heavy metals. Its anti-wear, energy efficient formula helps your bottom line.

HYDREX™ EXTREME is recommended for vane, gear and axial piston hydraulic pumps over an extremely wide range of operating temperatures. It is suitable for applications where systems must be started up at very low temperatures but have significantly higher temperatures during operation. It is also suitable for use in bucket trucks operating around power lines or in bucket truck hydraulic systems requiring extreme low temperature pumpability.

HYDREX™ EXTREME is suitable for use in Liebherr cranes where extreme cold temperatures occur.

Typical characteristics are shown below:

¹  Start-up is defined as the temperature at which the oil dynamic viscosity reaches 10,000 cP.

²  Operating temperature limits are determined by the equipment manufacturer. Petro-Canada Lubricants has chosen to define the upper operating temperature to be the after-shear oil kinematic viscosity of 10 cSt for mobile equipment and 13 cSt for industrial machinery, while the lower operating temperature to be the fresh oil dynamic viscosity of 750 cP for both mobile and industrial machinery.

These ranges are only an approximation and the operator should always check the viscosity requirements as specified by their equipment manufacturer. Mobile equipment typically refers to machinery that encompasses a transmission and braking system to allow and prohibit movement. Industrial machinery is typically stationary, with hard piping and auxiliary components in place.

HYDREX™ DT is a special anti-wear detergent/dispersant hydraulic fluid containing the same anti-wear and anti-oxidant chemistry as HYDREX™ AW. HYDREX™ DT also contains detergent/dispersant additives to help keep systems clean by helping to prevent deposit formation. This fluid is intended for use in hydraulic systems that are prone to contamination.

Typical characteristics are shown below: